Q: How much does garage door repair cost in Albuquerque?
A: Repair costs vary depending on the issue, such as a snapped spring or a faulty motor.Garage door repair costs typically range from $150 to $350 for common fixes like springs or sensors, with minor issues sometimes under $100 and major repairs reaching $800+
Spring Replacement (Torsion/Extension): $180 - $350 (parts & labor).
Off-Track Repair: $125 - $400.
Opener Repair / Replacement: $75 - $700
We provide transparent, upfront estimates before any work begins so there are no surprises on your final bill.
Q: Do you offer emergency garage door repair near me?
A: Yes! We provide 24/7 emergency services throughout the Greater Albuquerque area. If your car is trapped inside or your door won't close at night, give us a call immediately.
Q: How long do garage door springs usually last?
A: Most standard torsion springs are rated for 10,000 cycles (about 7–10 years). However, the dry New Mexico climate can sometimes lead to wear. If you hear a loud "bang," it’s likely time for a broken torsion spring repair.
Q: Can I repair my garage door myself?
A: While simple maintenance like lubricating tracks is fine, we strongly recommend professional help for spring replacements or cable repairs. These components are under extreme tension and can be dangerous to handle without the proper tools.
Q: What are the most common garage door repairs?
A: Garage doors are complex mechanical systems that undergo a high volume of stress. Statistically, broken springs are the most frequent issue, accounting for roughly 30% to 65% of all professional service calls.
Here is a breakdown of the most common repairs, categorized by their symptoms and severity.
1. Broken Springs (The #1 Repair)
Springs act as the "muscle" of the door, counterbalancing its weight so the motor can lift it.
The Issue: Most standard springs are rated for 10,000 cycles (roughly 7–10 years). When they snap, you'll often hear a loud "bang."
Symptoms: The door won't open at all, or the motor strains and only lifts it a few inches before stopping.
Danger Level: High. Springs are under extreme tension. This is generally not a DIY project as mishandling them can cause severe injury.
2. Misaligned or Blocked Safety Sensors
Safety sensors (photo-eyes) sit near the floor on either side of the door.
The Issue: These sensors must "see" each other to allow the door to close. They are easily bumped out of alignment or covered in dust/cobwebs.
Symptoms: The door starts to close but immediately reverses, often accompanied by a clicking sound or a flashing light on the opener.
The Fix: Clean the lenses with a soft cloth and ensure they are pointing directly at one another.
3. Snapped or Frayed Cables
Cables work in tandem with the springs to pull the door up.
The Issue: Over time, cables can rust, fray, or slip off their drums.
Symptoms: The door may hang crookedly, get stuck halfway, or appear to be "falling" on one side.
Danger Level: High. If a cable snaps, the door can slam down unexpectedly.
4. Worn Rollers and Hinges
Rollers are the small wheels that guide the door along the tracks.
The Issue: Plastic rollers crack, while steel rollers can lose their ball bearings or rust.
Symptoms: Excessive noise (grinding or squeaking), shaky movement, or the door vibrating as it operates.
Maintenance: Most rollers should be replaced every 5–7 years.
5. Track Realignment
The metal tracks on either side of the door must be perfectly parallel and straight.
The Issue: Tracks can be bent by a car bump or shift over time due to house settling or loose mounting bolts.
Symptoms: The door binds, rubs against the trim, or makes a loud scraping sound. Gaps between the rollers and the rail are a clear sign of misalignment.
Serving Albuquerque and the Surrounding Areas
We proudly serve residential and commercial clients across the Duke City, including:
NE Heights & Foothills
Taylor Ranch & Westside
Rio Rancho
South Valley
Corrales & Bernalillo
